Lesson 4.1: Metric Fasteners, Thread Callouts, and Hole Sizing
Technical Context
An FTC robot may use hundreds of fasteners, many of them M3 or M4. Their size, grade, engagement, and installation determine whether joints stay clamped through repeated impacts and vibration.
Reading a Fastener Callout
A complete callout looks like this:
M3 x 0.5 x 12 SHCS
| | | |
| | | +--- head style: socket head cap screw
| | +------- length in mm, under the head
| +------------- thread pitch in mm
+------------------ nominal major diameter in mm
Most common metric sizes have one standard coarse pitch, so it is usually written "M3 x 12" with the pitch implied. The pitch matters when you are tapping, which is why Module 2 covered it.
Length is measured under the head for most heads, and overall for flat countersunk heads, because a countersunk head sits inside the material. Ordering 12 mm flat head when you wanted 12 mm of shank gets you a screw that is short.
Head Styles and When Each Is Right
| Head | Recognize it by | Use when |
|---|---|---|
| Socket head cap (SHCS) | Cylindrical head, hex socket | Default for structure. Strong, high torque capacity |
| Button head | Domed low head, hex socket | Where clearance is tight or a snag hazard exists |
| Flat head (countersunk) | Conical underside | Where the head must sit flush with the surface |
| Set screw | No head at all | Locking a hub or collar onto a shaft |
Prefer socket head cap screws for anything structural. Button heads have a shallower socket and strip more easily under torque, and flat heads rely on the countersink being cut accurately to seat correctly.
Too short, and there is not enough thread engagement to carry load. Too long, and the screw bottoms out in a blind hole and stops pulling the joint tight, so the joint feels tight while carrying no clamping force at all. That failure is invisible during assembly and shows up as a joint that loosens in one match.
The Two Holes, Again
This was covered in Lesson 2.4 and is repeated here because it is the most common single mistake in FTC fabrication.
- The part the screw passes through gets a clearance hole, larger than the screw.
- The part the screw threads into gets a tapped hole, drilled at the tap drill size, which is smaller than the screw.
Tap Drill and Clearance Reference
Two different holes. Pick the wrong one and the joint is ruined.
The tap drill and the clearance hole differ by only 0.70 mm, which is why they are so easily swapped. Mark every hole on the drawing as TAP or CL before anyone picks up a drill.
| Thread | Pitch | Tap drill | Close fit | Free fit |
|---|---|---|---|---|
| M3 x 0.5 | 0.50 mm | 2.50 mm | 3.2 mm | 3.4 mm |
| M4 x 0.7 | 0.70 mm | 3.30 mm | 4.3 mm | 4.5 mm |
| M5 x 0.8 | 0.80 mm | 4.20 mm | 5.3 mm | 5.5 mm |
| M6 x 1.0 | 1.00 mm | 5.00 mm | 6.4 mm | 6.6 mm |
| #6-32 UNC | 0.79 mm | 2.71 mm | 3.8 mm | 4.0 mm |
| #8-32 UNC | 0.79 mm | 3.45 mm | 4.4 mm | 4.6 mm |
| #10-32 UNF | 0.79 mm | 4.04 mm | 5.1 mm | 5.3 mm |
| 1/4-20 UNC | 1.27 mm | 5.11 mm | 6.7 mm | 7.0 mm |
The default FTC fastener. Used across REV and goBILDA hole patterns.
A tapped hole receives the threads and must be drilled small. A clearance hole lets the screw pass through freely and must be drilled large. Drilling a clearance hole where you needed a tapped hole cannot be undone, so mark which is which on the drawing before anyone picks up a drill.
How a Bolted Joint Actually Carries Load
A properly made bolted joint does not carry load on the screw. Tightening the screw stretches it slightly, and that stretch clamps the two parts together. The friction between the clamped faces carries the load.
Three consequences:
Clamping force is the point. A screw that is snug but not tight provides little clamping force, so the joint relies on the screw in shear, and the parts shift within the clearance hole under load. That shifting is what you feel as slop.
Two fasteners resist rotation, one does not. A single screw through a bracket lets the bracket pivot around it. Two screws spaced as far apart as the bracket allows resist rotation directly. When a bracket keeps going crooked, the answer is a second screw, not a tighter one.
Washers spread the load. Under a screw head on soft material, a washer prevents the head from digging in and losing clamping force as the material deforms. On polycarbonate or printed plastic, a washer is not optional.
Most FTC hardware is stainless or alloy steel. Stainless resists corrosion but strips more easily. Alloy steel socket head screws are stronger and better suited to high-load joints. Avoid aluminum screws in structural joints unless the design specifically accounts for their lower strength.
Both holes measure the same from above. The only way to tell them apart without a section is that the screw in the stripped one turns without ever getting tight.
A photograph would show this better
A stripped M3 tapped hole in thin aluminum, photographed beside a good one in the same plate for comparison.Framing: Macro, both holes in one frame, angled light so the thread crests catch the light.Fill-in-the-Blank Practice
- In the callout M4 x 0.7 x 16, the number 0.7 is the thread
__________. - A bolted joint carries load primarily through the friction generated by
__________force, not through the screw itself. - When a bracket keeps rotating out of position, the correct fix is usually a second
__________rather than more torque.
Show answers
- pitch
- clamping
- fastener (screw)
Exercise
Find every single-fastener bracket on your robot. For each one, determine whether it can rotate about that fastener under load. Every one that can is a future alignment problem.
Ready to move on?
Only mark complete if you genuinely understand the material. Your progress will be saved in this browser.
Stuck on this lesson?
Ask about anything on this page. It can see which lesson you have open and which part you are reading.